如何清潔蒸發器：完整的維護指南

乾淨的蒸發器性能更好，味道更好，使用壽命更長。 定期維護可防止氣道堵塞、燒焦的味道和最終的設備故障。 本指南涵蓋從快速每天清潔到每月深度維護的所有內容。

快速回答

快速清潔：每次使用後清空，每週刷掉殘留物。 深層清潔：拆卸，將金屬/玻璃零件浸泡在 90% 異丙醇中 20 分鐘，用酒精擦拭室，用管道清潔器清潔蒸氣路徑，重新組裝前完全乾燥。 永遠不要淹沒電子產品。

---

為什麼清潔很重要？

跳過蒸發器維護導致：

• 氣流受限: Resin Buildup Clog 螢幕和蒸氣路徑
• Bad taste: 舊殘留物會產生灼熱、陳舊的味道
• 效率降低: 髒的房間不能均勻加熱
• 設備故障: 樹脂會損壞電子產品和密封件
• 健康問題: 黴菌會長在骯髒、潮濕的殘留物中

乾淨的電子煙 = 純味 + 輕鬆抽獎 + 一致的性能

---

您需要清潔用品

Essential:

• 90%+ 異丙醇
• 棉花棒（Q-Tips）
• 小刷子（通常包含在蒸發器中）
• 紙巾
• 旚

Helpful:

• 管道清潔器
• 牙籤（用於頑固的殘留物）
• 超細纖維布
• 壓縮空氣（可選）
• 超音波清潔器（可選，重度使用者）

Never use:

• 丙酮或指甲油去除劑
• 用添加劑外用酒精
• 刺激性化學物質或溶劑
• 砂洗機
• 過多的水（尤其是在電子設備附近）

---

清潔時間表

每次會議後（1 分鐘）

怎麼辦：

1. 讓蒸發器冷卻

2. 完全清空房間

3. 快速刷子去除鬆散的材料

4. 輕輕地吹過蒸氣路徑

Why: Prevents buildup from hardening and becoming difficult to remove.

每週快速清潔（5 分鐘）

怎麼辦：

1. 徹底刷牙

2. 檢查螢幕是否有堵塞

3. 用酒精擦拭喉舌

4. 如果需要，快速酒室擦拭

Why: Maintains optimal airflow and flavor between deep cleans.

深度清潔（每 10-20 節或每月）

怎麼辦：

按照下面的完整分步指南。

Why: Removes all accumulated resin, restores like-new performance.

---

步子

步驟 1：冷卻並清空

切勿清潔熱蒸發器。 Let it cool completely (10-15 minutes after use). Hot alcohol is dangerous and can damage components.

從房間中取出所有用過的大麻。 輕輕敲掉，然後徹底刷。

步驟 2：拆解你能做的

大多數蒸發器都有可拆卸的部件：

• Mouthpiece
• 螢幕（房間和喉舌）
• 玻璃零件（如果適用）
• 矽膠蓋或環

檢查你的手冊 for what's meant to come apart. Don't force anything.

追蹤小零件！ Screens especially are easy to lose.

步驟 3：浸泡金屬和玻璃零件

浸泡什麼：

• 金屬屏風
• 玻璃喉舌
• 玻璃組件
• 金屬工具

什麼不浸泡：

• 電子（電池、顯示器、加熱元件）
• 橡膠墊圈和 O 型環（短接觸可以，不要長時間浸泡）
• 矽膠零件（簡短接觸 OK）
• 蒸發器的主體

Method:

1. 將零件放入小容器中

2. 用 90% 以上的異丙醇覆蓋

3. 浸泡 15-30 分鐘

4. 輕輕攪拌以鬆開殘留物

5. 用牙籤做頑固的斑點

步驟 4：清潔房間

這是最重要的一步。 The chamber accumulates the most residue.

1. 將棉花棒浸入異丙醇中（擠壓過量）

2. 以圓周運動輕輕擦拭室內牆壁

3. 旋轉拭子以使用乾淨的部分

4. 根據需要使用新的拭子

5. 繼續直到棉籤乾淨（不是棕色）

Tips:

• 不要將酒精滴入設備中
• 在加熱元素周圍溫柔
• 進入角落和邊緣
• 使用前讓腔室完全乾燥

步驟 5：清潔蒸氣路徑

將腔室連接到口腔的管子會收集凝結的蒸氣殘留物。

對於可訪問的路徑：

1. 將管道清潔器浸入酒精中

2. 插入並扭轉路徑

3. 用新鮮的管道清潔劑重複直到清潔

對於狹窄或無法進入的路徑：

1. Use thin cotton swabs

2. Or run a "burn-off" session (heat empty vaporizer to high temp for 30 seconds)

Step 6: Clean Screens Thoroughly

Clogged screens drastically restrict airflow.

Method:

1. If screens were soaking, remove from alcohol

2. Brush both sides to remove loosened residue

3. Hold up to light—you should see through cleanly

4. If still clogged, soak longer or replace

Replacement: Screens are cheap ($5-10 for packs). Replace when cleaning doesn't restore full airflow.

Step 7: Rinse (Optional) and Dry Completely

Optional rinse:

Some people rinse alcohol-cleaned parts with warm water to ensure no alcohol residue remains. This is fine but extends drying time.

Critical: Complete drying

• Lay all parts on paper towel
• Let air dry for at least 30-60 minutes
• Use hair dryer on LOW setting to speed up (no heat on electronics)
• Blow through parts to check for remaining moisture

Never reassemble and use a wet vaporizer. Alcohol residue tastes awful and moisture near electronics causes damage.

Step 8: Reassemble and Test

1. Ensure all parts are completely dry

2. Reassemble in reverse order

3. Run a brief empty heat cycle (burn off any remaining residue)

4. Pack normally and enjoy improved performance

---

Device-Specific Tips

Conduction Vaporizers (Pax, DaVinci)

• Chamber walls need extra attention
• Residue builds up from direct contact
• Use screen trick: place screens on top of material to keep chamber cleaner

Convection Vaporizers (Mighty, Firefly)

• Less chamber buildup
• More vapor path residue
• Focus on cleaning airways

Portable with Glass Parts (Arizer)

• Glass stems collect visible residue
• Make "stem milk" by simmering in milk to extract reclaim
• Glass is easiest to clean with alcohol soak

Desktop Vaporizers

• Larger parts but same principles
• Bags/balloons should be replaced periodically
• Whip tubing can be replaced or soaked in alcohol

---

Troubleshooting After Cleaning

Issue: Harsh taste after cleaning

• Cause: Alcohol residue remaining
• Fix: Dry longer; run empty heat cycles

Issue: Airflow still restricted

• Cause: Missed clogs in screens or vapor path
• Fix: Re-check screens, repeat vapor path cleaning

Issue: Parts don't fit after cleaning

• Cause: Gaskets displaced or missing
• Fix: Check O-rings and gaskets, ensure proper positioning

---

Extending Time Between Deep Cleans

Use dosing capsules: Many vaporizers offer metal pods that contain cannabis and keep the chamber cleaner. Empty the pod, not the chamber.

Brush after every session: 10 seconds of brushing prevents hardened buildup.

Use screens on top of material: Prevents particles from contacting chamber walls directly.

Don't overheat: Excessive temperatures create more stubborn residue.

---

This guide is for educational purposes. Always follow your vaporizer manufacturer's cleaning recommendations.